this post was submitted on 18 Dec 2024
1118 points (98.6% liked)
memes
10698 readers
2967 users here now
Community rules
1. Be civil
No trolling, bigotry or other insulting / annoying behaviour
2. No politics
This is non-politics community. For political memes please go to !politicalmemes@lemmy.world
3. No recent reposts
Check for reposts when posting a meme, you can only repost after 1 month
4. No bots
No bots without the express approval of the mods or the admins
5. No Spam/Ads
No advertisements or spam. This is an instance rule and the only way to live.
Sister communities
- !tenforward@lemmy.world : Star Trek memes, chat and shitposts
- !lemmyshitpost@lemmy.world : Lemmy Shitposts, anything and everything goes.
- !linuxmemes@lemmy.world : Linux themed memes
- !comicstrips@lemmy.world : for those who love comic stories.
founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
Ethernet is obviously better but running ethernet around your home can be a pain in the arse
A pain in the arse you only need to do once, and you can hire someone to do it for you for basically the same cost as a couple of the high end wireless routers, so in like 5 years, you break even.
Also, how much have you spent on your computer (s), phone(s), tablet(s), and all your other internet connected devices, and you won't spend like $500 on something that can run all that stuff simultaneously? Pouring literally thousands of dollars on connected devices, but most won't pay more than they would for a toaster, to get them on the internet, then pay out the wahzoo for gigabit internet that your crummy d-link router can't handle, and you wonder why all your fancy gadgets run like shit.... It's a lot like buying a Ferrari to drive on dirt/gravel roads.
I think it’s a little more than $500 to get Ethernet ports installed all around your house. Especially if you need to run through fire breaks and insulation. Will have to wait till a remodel before I can get those installed.
That said, I didn’t skimp on my home networking, even though it’s all wireless. I’ve got 4 WiFi 6 APs on PoE with Cat 6 runs thru the attic. I can get 700 Mbs+ download speeds pretty much anywhere in and around the house.
It could be, depending on where you land on the DIY vs building code spectrum.... Also what your local building code details in terms of low voltage cable.
In my experience unless you're intentionally going through air handling ductwork, CMG is fine, though I would go with CMR at least, just as a matter of safety. I have yet to see a residential home with any fire protection or fire breaks, at all, nevermind where you would think to put them, like between floors and whatnot. The homes in my area are mostly built from timber, so we're basically living inside a framework of dried out wood, so putting a fire break between wood framed floors where the floor/ceiling shares a set of wooden cross members for support, seems like it would be unnecessary, since the framing of the building is going to conduct the fire between levels.
Ethernet is low voltage, so it's largely unregulated. The only real regulation is regarding plenum or riser spaces, and the latter is mostly when floors are intentionally or naturally separated in terms of shared fate when it comes to fire. I only see fire breaks in concrete structures, usually apartments or commercial buildings.
YMMV, not every country has the same building codes, so every person reading this will need to do their own research or pay someone who knows.
My point remains, regardless of all this conjecture: even if it's $2000 or more, this is structure cabling that should service the premise for as long as it continues to stand, which is hopefully many decades. Over 20 years, at $2000 for installation, you're looking at a cost of around $8.34/mo for the cabling to exist.
Considering people will pay 10x that for Internet service, and the addition of Ethernet in the building will allow them to take full advantage of the internet they're paying for, I'd call that a bargain.
You will generally run into fire stops in the framing, like you can see here:
https://www.oneprojectcloser.com/fire-stops-fire-blocking-in-studs/
When I ran wires to my office, I had to cut out one section of drywall above it, another below it, and then use a right angle attachment for my drill to go through it. Pull wire through and seal it with fire block foam.
Seems pointless considering the fire stop is made from something flammable.
Its purpose is to slow it down, not stop it. There would be a chimney effect where smoke rises out of the channel and fresh oxygen is allowed to come in from below. The blocks here prevent that from happening.
Oh, I'm not saying it's not functional in stone capacity. I understand the physics and what is trying to be accomplished with it, but unless it's done with pretty tight tolerance so any air leakage between the upper and lower spaces is as close to nil as possible, then it's not going to be super effective.
Dude, this is standard framing that's been done for ages and is in tons of houses in the US. It works, and it's mandated by code for a reason.
I'm not disputing any of that. I'm just saying that it seems like it wouldn't work super well.
I'm just some guy on the internet. I'm expecting an opinion. I don't wish to suggest we should do away with it because it's probably not the most helpful thing we could do; not at all. Keep it, use it, be happy and hold a parade.
I still think that it's not as effective as it could be because you'll always have air leak, and probably enough that putting a small hole in a fire break to run a cable probably won't make things much worse.
Code says you have to seal it, so that's what you'd be obligated to do. I'm only questioning if there's better options that would be more effective. That's all.
Preach! I just finished a long DIY remodel and running ethernet to everyroom was less than a $100 in cable and connectors. Obviously it was easier and cheaper for me because I already had a lot of the drywall down.
Either way such a good point you make, people will drop 1k on a phone no questions asked but a few hundred is too much to get the best home upgrade a tech enthusiast could ever ask for.
So far, I'm only £150 down on cable and clips on my rennovation. And this is the decent stuff, AWG23, and double run.
It'll probably go sideways when I spec up a switch with enough ports, mind...
I could preach all day about this.
I have a simple philosophy: wired when you can, wireless when you have to.
With that being said, doing a site survey for wifi and getting optimal access point locations, then placing Ethernet in ceiling there for said access points, ensures you have good coverage of your space, which then leads into another rant about network hardware and people spending thousands on everything except their router/access points even if they have the structure cables to support such a system....
Then people wonder why their wifi sucks.
I mean, spend a couple hundred one time to get Ethernet run, spend some time on an online ap placement tool and signal estimator for it, and then go buy infrastructure wireless for your home, and spend upwards of $1000 on networking hardware. You'll get more out of it and it will work for longer than your $1000+ smart phone, or many $1000s laptop that use it almost constantly.
Networking is critical and it should be seamless and blend into the background. You shouldn't need to mess with it constantly to get it to work. If that's normal for you, then something is very wrong.
Or if you rent. I could run an Ethernet cable to my office from my router, but it would have to run upstairs and across a few doorways.
Way less so if your home is constructed such that the wireless is borked
That can be an advantage. Some of the enterprise-level tech has trickled down to consumer WiFi in recent years, which includes browsing between multiple access points. With several access points with relatively weak signal, you get signal right where you need it without broadcasting up and down the street.