this post was submitted on 14 May 2024
37 points (97.4% liked)

3DPrinting

15591 readers
9 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee
37
[Troubleshooting] Big stringing problem with flsun SR and Orcaslicer (lemmy.nz)
submitted 6 months ago by Rangelus@lemmy.nz to c/3dprinting@lemmy.world
11 comments fedilink hide all child comments
 

Ok guys, I'm breaking down and posting here to see if anyone has any ideas. I'm greatful for any advice.

I have an upgraded flsun SR. I recently lost my computer (psu issue, waiting for replacement) and I took this opportunity to switch from Cura to Orcaslicer.

Over-all I'm very happy, and getting some good speeds, but I just cannot remove stringing no matter what I try:

  • Retraction from 0-7mm. After about 3mm, no further effect
  • Retraction speed from 30mm/s-50mm/s. No noticable effect
  • Travel speed and acceleration both high (up to 350mm/s and 6000 accel. No effect
  • Temp from 205-215 with no effect
  • Dried filament and different colours, no effect
  • Wipe on retract on and off, up to 2mm wipe distance and 100% retraction. No effect
  • Messed with scarf seams on and off, no effect
  • No effect from layer heights

My setup:

  • Printer - FLSun SR running klipper with a speede pad
  • Filament - Esun PLA+
  • Upgrades - Deported fans, OMG v2 extruder, volcano hotend and high flow cht nozzle
you are viewing a single comment's thread
view the rest of the comments
[–] Rangelus@lemmy.nz 2 points 6 months ago (1 children)

I know esun is quite popular, but I never tried it.

I've generally had the best results with it. Ironically, before the upgrades I had almost no stringing.

I'm using a 0.4mm nozzle. I probably should have mentioned in the OP that I didn't have problems before, but the upgrades have happened in addition to moving to Orcaslicer.

Now I'm worried if I've got my Bowden tube seated in the hotend correctly...

[–] rambos@lemm.ee 4 points 6 months ago (1 children)

Now I’m worried if I’ve got my Bowden tube seated in the hotend correctly…

Just pull/push the tube with your hands. If there is no play you are good, but if there is:

  1. Inspect the bowden tube ends and cut them if they are worn out
  2. Push the bowden tube in the fitting.
  3. While pushing it in, press the collet down
  4. Then pull it out with a nail and then zip tie it

I found original clips too thin, zip ties are much better IMO. It helped me remove stringing completely while using half of the retraction distance (using 0.6 nozzle)

[–] Rangelus@lemmy.nz 1 points 6 months ago

After sleeping on it, I remembered that my new heatbreak doesn't feed the bowden all the way to the end of the nozzle like the stock one does, so I'm pretty sure I have it seated correctly. I'll check it though, many thanks for the info! :)