this post was submitted on 06 Jul 2023
17 points (100.0% liked)

PC Master Race

14954 readers
1 users here now

A community for PC Master Race.

Rules:

  1. No bigotry: Including racism, sexism, homophobia, transphobia, or xenophobia. Code of Conduct.
  2. Be respectful. Everyone should feel welcome here.
  3. No NSFW content.
  4. No Ads / Spamming.
  5. Be thoughtful and helpful: even with ‘stupid’ questions. The world won’t be made better or worse by snarky comments schooling naive newcomers on Lemmy.

Notes:

founded 1 year ago
MODERATORS
Brunbrun6766@lemmy.world
_MoveSwiftly@lemmy.world
Xeon@lemmy.ml
IowaMan@lemmy.world
The_Vampire@lemmy.world
CatZoomies@lemmy.world
geosoco@kbin.social
Fudgeknuckles98@lemmy.world
BobaFett26@lemmy.world
17
can't fix RAM voltage on a Gigabyte B450 Aorus Elite (lemmy.ml)
submitted 1 year ago by dingdongitsabear@lemmy.ml to c/pcmasterrace@lemmy.world
20 comments fedilink hide all child comments
 

I have a Ryzen 5 1600AF (Zen+) and 2x 8 GB DDR4 3600 HyperX. when I select XMP1, it says 1.35V in the profile. however, when I boot Strelec WinPE USB (I'm on Fedora, I really don't want to install windows just so I can run HWINFO), install all drivers and launch HWINFO64 it says 1.2V. so I enter BIOS again, go to Voltages and enter 1.35 manually instead of auto. no change, still reads 1.2V. the BIOS side screen shows 1.35 after reboot.

I've found an unresolved thread somewhere with the same problem for my board. I'm on latest BIOS.

am I missing something, is there some additional setting I need to switch so it registers? the BIOS setup is hella confusing and borderline stupid, e.g. enabling virtualization required turning on SMP (how am I supposed to guess what that is?!) that's located in the "Frequency" subsection (wtf?!).

you are viewing a single comment's thread
view the rest of the comments
[–] SteveTech@programming.dev 2 points 1 year ago (1 children)

Yeah it does need a sensors config for your motherboard too, if you want the proper names, but I won't be able to get mine until maybe Sunday.

[–] dingdongitsabear@lemmy.ml 2 points 1 year ago (1 children)

I'm mainly checking if there's something else to switch in BIOS or that's all there is to it and my setup is just incompatible; I'm waiting to snag a used 5600 when they drop a bit more in price, since they're supposed to work better with faster RAM. but sure, if you get around to it I'd appreciate any config you can share.

[–] SteveTech@programming.dev 2 points 1 year ago (1 children)

Here's my sensors config: https://github.com/frankcrawford/it87/pull/12/files

  • BIOS is set to 1.35
  • sensors reports 1.38
  • dmidecode reports 1.2

So I believe the motherboard is running my ram at the correct voltage, just the dmi is hard coded.

[–] dingdongitsabear@lemmy.ml 1 points 1 year ago (1 children)

my original reply vanished, so here I go again: thank you very much for your efforts and for following up. I couldn't get the driver to compile on my system but that wasn't my primary goal, guess my setup is just incompatible. hopefully I'll get a used 5600 by year's end and check then. thanks again.

[–] SteveTech@programming.dev 1 points 1 year ago* (last edited 1 year ago)

No worries!

I believe for the driver you need to install ~~build-essential~~ @development-tools (forgot about fedora) and then run sudo make dkms.