And when pulling it out from the mess of cables
Memes
Rules:
- Be civil and nice.
- Try not to excessively repost, as a rule of thumb, wait at least 2 months to do it if you have to.
Or when your're trying to feed that fucker back through the passthrough on a desk.
Left side: Unscrews from the standoff. Right side: Unscrews the standoff from the IO plate.
Every fucking time. Why do I keep buying monitors with a VGA 🤣😭
But seriously, why would you buy a VGA monitor in 2024?
(Edit: typo)
Fighting games and the absolutely lowest possible video latency with the tech available. VGA puts you literally a frame or two ahead of the opponent. For players at their peak, this is a pretty big advantage.
You have to tighten the loose one to loosen the tight one. My fingers hurt just looking at it
you a director yet? that's gandalf level wisdom
Amen to this....or just say fuck it and break out the screwdriver
You mean that thing I set down right there but has somehow transitioned into a different dimension?
Best part is when this sucker unscrews from the port and comes off with the cable:
Ugh this stresses me out just thinking about it
The actual retro problem was when those tighty boys would start unscrewing the port instead of themselves
Pretty sure the little slit was so that you could use a flathead screwdriver. Had to do that a couple times
Then one side of the driver notch shears off
those slots were near useless.
edit to say: one trick was to use the blank expansion slot plates to gently break the vice like grip the screw had in the hex stand-off. the metal used on the cheap "digit remover" cases was sometimes soft enough to loosen the thumb screws via the driver slot without the thumb screw breaking.
still nearly useless though.
This happens because the connector is at an angle. Since it's at an angle, the screw presses against the side and jams itself in place. All you have to do is tilt the connector the other direction and the tight screw loosens right up. Easy peasy.
This would have been really good for me to know about 20 years ago.
Holy Diver!
Retro problem? I used a DVI connector on my monitor until December last year.
Am I the only one that never tightened them?
I tighten them and it saved my monitor! Robbers broke in to our house, stole a bunch of stuff. The computer monitor was still there, connected to the computer, dangling from the table.
How do I know they tried to steal it? Because they tried to cut through the cable with PAPER SCISSORS, because they didn't know how to unscrew the cables.
I feel sorry for the dumb robbers. I hope they didn't pawn it and are still enjoying playing Wii Fitness without the balance board, which they neglected to take with the console.
GPIB users and instrumentation automating folks know the problem is very modern.
also, both stripped somehow?
I still have a DVI monitor connected to my main pc, so it's not that much of a retro problem for me
I like DVI. I prefer it most of the time.
I like the screw in connector because I don't have to worry about it falling out of the PC or monitor, and it is more robust, less likely to be pulled/bent/broken.
Unfortunately, even monitor vendors don't seem to agree that DVI was/is good, and I've seen a lot of displays shipping without it recently. GPU makers have entirely gone to displayport/HDMI. It's the end of an era, as far as I'm concerned.
I've switched almost entirely to DP, since I can't get DVI anything anymore. I don't hate DP. I like it more than the friction fit HDMI which is prone to pulling itself out of the port for no good reason just as your opponent is about to come around the corner and all you can do is stare at yourself in the black mirror that your monitor has become and listen in horror as fartmaster69420 frags you again, bragging about it and telling you that you suck, and how he does unspeakable things to your mother over VC in his prepubescent voice.
Anyways. I miss DVI.
All I can say is that we are fortunate that the overlap between "VGA ports everywhere" and "battery operated impact drivers" is almost zero on the timeline. Imagine trying to unscrew a VGA plug by hand that was tightened down to ugga-dugga-foot-pounds of torque. Of course that assumes that didn't shear the screws first.
At least they had screws? I dont trust HDMI or even worse USB-C. Still using VGA monitors with adapters, never broke a single plug.
I sort of miss the screws too but it's so much better when a cable accidentally gets yanked and it just comes right out instead of transmitting the force into whatever it's attached to.
Good news, USB-C has two formats with screws: 1 on either side like VGA or 1 on top. Though I've never seen them in real life.
Why are you using VGA when DVI-D exists? Or Displayport for that matter.
Because VGA used to be a standard and all monitors I had lying around are VGA only